Sinuo Testing Equipment Co. , Limited
| Payment Terms | T/T |
| Supply Ability | 15 Sets per Month |
| Delivery Time | 1 Month |
| Packaging Details | Plywood |
| Power supply | AC120V±10%, 60Hz |
| Working stroke | 35mm |
| Test times | 1~9999 |
| Rate of test | 60 times /min |
| Weight | 10N*1, 60N*1, 20N*2 |
| Cord bushes | 5 pieces |
| Model | SN2120 |
| Standard | IEC60884-1 |
| Brand Name | Sinuo |
| Model Number | SN2120 |
| Certification | Calibration Certificate (Cost Additional) |
| Place of Origin | China |
View Detail Information
Explore similar products
75g Test Punch With 60° Conical Tungsten Carbide Tip IEC60335-2-24 Clause 22.116
IEC 60335-2-23 Skin or Hair Care Appliance Swivel Connection 50 r/min Rotation
IEC 60335-1 Oxygen Bomb Aging Test Chamber 4000cm3 Stainless Steel Air Bomb Tank
SS Electrical Appliance Tester IEC 60335-1 Clause 20.2 Similar To Test Probe B
Product Specification
| Payment Terms | T/T | Supply Ability | 15 Sets per Month |
| Delivery Time | 1 Month | Packaging Details | Plywood |
| Power supply | AC120V±10%, 60Hz | Working stroke | 35mm |
| Test times | 1~9999 | Rate of test | 60 times /min |
| Weight | 10N*1, 60N*1, 20N*2 | Cord bushes | 5 pieces |
| Model | SN2120 | Standard | IEC60884-1 |
| Brand Name | Sinuo | Model Number | SN2120 |
| Certification | Calibration Certificate (Cost Additional) | Place of Origin | China |
| High Light | Cord Retention Testing Apparatus ，IEC 61851-1 Cord Retention Testing Apparatus ，Rewirable Plugs Cord Retention Testing Apparatus | ||
IEC 61851-1 Cord Retention Testing Apparatus For Testing Rewirable Plugs
Product information:
This device conforms to the standard requirement of IEC60884-1 clause 23.2 figure 20. It is for testing rewirable plugs and rewirable portable socket-outlets shall be provided with a cord anchorage such that the conductors are relieved from strain, including twisting, where they are connected to the terminals and that their covering is protected from abrasion. The machine conducts automatically after the test started; it will stop working after reaching the setting number of times.
Technical parameters:
| Power supply | AC120V±10%, 60Hz |
| Number of test | 1~9999(it is adjustable.100 is by default |
| Rate of test | 60 times /min |
| Weight | 10N*1, 60N*1, 20N*2 |
| One set of cord bushes | 5 pieces (each ofΦ6mm, Φ8mm, Φ10mm, Φ12mm, Φ16mm) |
| Working stroke | 35mm |
1. Before install the test sample, can left rotate the speed adjust button to make the speed to be slower, observe when the mechanical arm moves down to the lowest position, press down the STOP button immediately.
Note: the speed adjust button is used to adjust the speed of the motor, thus to adjust the mechanical arm’s action speed. Right rotate this button to speed up, left rotate to slow down. When operator rotates the speed adjust button to make the mechanical arm action speed to match standard requirements, for example, 60 times/min (manually check by a stop watch), operator can mark the position, then next time test, operator just need to rotate the button to the mark position.
2. Loose the up cord clamp, select the appropriate cord bush (refer to the table below) according to the specifications of the sample, insert the cord bush into the entrance hole, then the cord of the specimen are across the cord bush, clamped by the up and lower cord clamps. After that, choose the appropriate weight based on the weight of the test requirements, the weights are hanged on the end of the cord, adjust the weight to the appropriate height, and the test can be started.
3. Access to the power supply, preset the test times on the counter.
Press “RESET” to clear the display value, then press the “RUN” button, the test starts, the test will automatically stop when reach to the setting times, press the “STOP” button when you want to stop during the half-way.
Attention:
1. Lubricating oil should be added on the movable end of the guide rail regularly, to ensure that the test machine running smoothly
2. The flexible cord should be kept in vertical after the weights are hung on the cord, and the weight should be hung firmly to avoid falling during working, and damage the equipment, it is better to add a rubber plate on the bottom plate.
3. In normal use, the warranty period of the equipment is one year, we will continue to provide technical service after the warranty period.
Company Details
Business Type:
Manufacturer
Total Annual:
800000-1500000
Employee Number:
30~50
Ecer Certification：
Verified Supplier
Sinuo is an innovation manufacturing company, specializing in the research and development and sales of laboratory construction and testing equipment for electrical appliances (covering the construction of energy efficiency and performance laboratories, as well as supplementary waterproof testing la... Sinuo is an innovation manufacturing company, specializing in the research and development and sales of laboratory construction and testing equipment for electrical appliances (covering the construction of energy efficiency and performance laboratories, as well as supplementary waterproof testing la...
Get in touch with us
Leave a Message, we will call you back quickly!