Heavy-Duty Carrier Condenser Fan Motor 54-60006-10 with 12V / 14V DC and 2200

Product Specification

Carrier Condenser Fan Motor 54-60006-10 — 12V / 14V DC, 2200 RPM — Detailed Product Description

Product Description

The 54-60006-10 condenser fan motor is a heavy-duty direct-replacement motor intended for truck and trailer refrigeration condenser assemblies. Rated for 12V / 14V DC operation and a nominal speed of 2200 RPM, it is engineered to provide consistent, high-volume airflow for effective heat rejection in transport refrigeration applications. The motor is manufactured for continuous duty in harsh environments—exposure to vibration, temperature cycling and roadside conditions—so durability and reliability are primary design objectives.

Mechanically the unit is built with a rugged metal housing and precision bearings to withstand axial and radial loads imposed by fan blades and beltless direct-drive configurations. The rotor and fan coupling are dynamically balanced at the factory to minimize vibration and bearing stress, which reduces noise and extends service life. Electrical windings and insulation are designed to tolerate the transient conditions typical in vehicle electrical systems; connectors are corrosion-resistant and intended for OEM harness compatibility.

This motor is suitable for field replacement during routine maintenance or as part of a condenser assembly overhaul. It restores condenser air movement and overall system cooling capacity when an original fan motor has failed, seized, or degraded in performance.

Key Features & Benefits

• Durable metal housing with corrosion-resistant finish for long life in outdoor and marine-exposed environments.

• Designed for continuous duty at 12V / 14V DC system voltages; nominal speed ~2200 RPM for strong condenser airflow.

• Factory dynamic balancing to minimize vibration, noise and premature bearing wear.

• High-quality sealed bearings (pre-lubricated) for low maintenance and extended service intervals.

• OEM-style electrical connector for straightforward plug-and-play replacement where applicable.

• Compact footprint and standard mounting pattern to facilitate rapid swap-out on compatible Carrier condenser assemblies.

• Bench tested for smooth operation and mechanical runout prior to shipment.

Installation & Electrical Connection (Recommended Procedure)

Safety first: isolate vehicle power (battery disconnected) and follow OEM service instructions. Installation should be performed by a qualified technician.

1. Preparation: Verify the replacement motor matches the original part number (54-60006-10) and confirm voltage (12V or 14V) against the vehicle/system electrical supply. Inspect wiring harness and connectors for damage.

2. Removal: Safely remove the condenser access panels, disconnect the electrical connector, and remove mounting fasteners holding the old motor or fan assembly. Use appropriate tools to avoid distorting mounting surfaces.

3. Mounting: Fit the new motor to the condenser bracket or housing with the original fasteners. Ensure the motor is seated squarely and torque bolts to the manufacturer’s recommended values. Misalignment can cause vibration and premature bearing failure.

4. Electrical Hook-up: Connect the motor to the electrical harness using the OEM connector. If hard-wiring is required, use properly sized wire and an appropriately rated fuse or circuit breaker in the supply line. Confirm correct polarity where applicable.

5. Pre-start Checks: Rotate the fan by hand (if possible) to check for interference. Reconnect battery/power and briefly energize to verify rotation direction and smooth operation. Monitor for abnormal noise, smoke or excessive current draw.

6. Functional Test: Run the refrigeration unit through typical duty cycles and confirm adequate condenser airflow, stable system pressures and normal compressor loading. Re-check fasteners and wiring after initial run-in period.

Notes: Always fit a fuse sized per the motor/vehicle specifications. If the original motor used thermal protection or an internal tachometer, confirm equivalent protections are present or provided externally.

Maintenance & Troubleshooting

Routine maintenance:

• Periodically inspect connector and wiring for corrosion, chafing or loosened terminals.

• Clean external dirt, dust and debris from the motor housing and fan blades to maintain airflow.

• Monitor for increasing bearing noise, vibration or reduced airflow — these are early signs of wear.

Troubleshooting checklist:

• Motor does not run: verify fuse, supply voltage at connector, and continuity of wiring; check for seized rotor.

• Motor runs but slow / weak airflow: confirm supply voltage under load; inspect for mechanical binding or damaged fan blades.

• Excessive noise or vibration: check mounting fasteners, dynamic balance, and bearing condition; replace if bearings are worn.

• Intermittent operation: inspect connectors for corrosion or loose terminals and check for overheating/thermal cutouts upstream.

When replacing a motor, inspect the fan blades and mounting hardware; a fresh motor on a damaged fan will still produce poor performance.

Compatibility, Ordering & Packaging

• Confirm fitment: This motor is sold as a replacement part for Carrier condenser applications that list 54-60006-10. Always verify OEM part number and vehicle/unit model prior to ordering. If uncertain, provide the refrigeration unit serial number and existing part number to your supplier.

• Variants: Some Carrier motors have close variant part numbers with different connector types, mounting flanges or voltage ratings. Confirm exact variant to avoid incompatibility.

• Packaging: Supplied new in protective packaging with connector protection and mounting hardware where indicated. Bulk or OEM-branded packaging available on request.

• Warranty: Standard limited warranty (typically 12 months) against manufacturing defects—confirm with supplier.

Product Specifications

After-Sales & Support

We provide technical fitment assistance if you supply your unit model and serial number. Options typically available include single-unit supply, bulk fleet orders, and remanufactured exchange programs (subject to availability). For fleet operators we can advise on spares stocking levels and provide accelerated shipment for emergency replacements.

FAQ

Q1:When will you arrange the delivery?

A:Generally 1-2 weeks after the payment, and we will continually inform customer the goods carriage status, until you receive the goods.

Q2. Do you test all your goods before delivery?

A: Yes, we have 100% test before delivery.

Q3:Can we get the some technological training?

Our company provide the complete technological training, including: installation, use and maintenance.

Q4:How long is your products warranty?

A:The products of our lifetime for you to provide maintenance, one year warranty,Courier fees to pay half, after a year of maintenance fees shall be borne by the buyers.

Q5: How do you make our business long-term and good relationship?

A:1. We keep good quality and competitive price to ensure our customers benefit ; 2. We respect every customer as our friend and we sincerely do business and make friends with them, no matter where they come from.