A Comprehensive Guide to Polyaspartic

Product Specification

Polyaspartic is a high-performance, aliphatic, two-component elastomer coating. It is formed through a rapid addition polymerization between polyaspartic resin (usually the A component) and isocyanate prepolymer (usually the B component) at room temperature. Although it's part of the polyurea family, the presence of polyaspartic resin gives it distinctive properties—especially notably extended working time (gel time) and superior weather resistance.

The chemical reaction formula:

R–NCO + R′–NH₂ → R–NH–CO–NH–R′

Core Features & Advantages of Polyaspartic

1. Exceptionally Long Working Time

One of the most prominent advantages. Compared to traditional aromatic spray polyurea (gel time often a few seconds to tens of seconds), Polyaspartic can have gel times ranging from several minutes to several hours, by adjusting components such as the type and activity of polyaspartic resin in Part A, as well as catalyst type and dosage. This offers:

• Use of common spraying equipment (low-pressure or airless spray), brushing, or rolling.
• Reduced equipment requirements and easier application.
• Better for large areas, complex shapes, repairs, and reworks.
• Less material waste due to prolonged usable time after mixing.

2. Excellent Weather Resistance & Gloss/Color Retention

• Aliphatic nature provides outstanding UV resistance—resists yellowing and chalking.
• Retains initial gloss and coloration over long periods.
• Ideal for applications demanding long-term aesthetic performance under outdoor exposure (e.g., architectural exteriors, floor finishes, wind turbine blades).

3. Fast Curing & High Productivity

• Despite long working time, it cures rapidly once gelation begins.
• Reaches tack-free or walkable state within a few hours.
• Achieves most performance characteristics within 24–48 hours.
• Significantly shortens construction cycles and boosts efficiency.

4. Outstanding Physical-Mechanical Performance

• Balanced high hardness and flexibility/elastomeric properties.
• Superior abrasion resistance—far exceeding epoxy resin and comparable to traditional polyurea.
• Excellent impact resistance—resists cracking or delamination under force.
• Strong adhesion to various substrates (concrete, steel, aluminum, old coatings) with appropriate primer.

5. Excellent Chemical Resistance

• Resistant to acids, bases, salts, solvents, oils, protecting substrates from corrosion.

6. Low VOC, Environmental Friendliness

• Typically 100% solids or high solids formulation (very low VOC), compliant with strict regulations.
• Solvent-free, safe for the work environment, and reduces fire hazard risk.

7. Wide Applicability to Conditions

• Less sensitive to temperature and humidity variations compared to traditional polyurea, enabling a broader range of construction conditions—subject to product specifications.

8. Highly Tunable Formula

• By modifying polyaspartic resin structure, molecular weight, functionality, reactivity, plus variations in isocyanate prepolymer type and NCO content, one can tailor final coating properties—hardness, flexibility, cure speed, gloss, etc., to meet different application needs.

Comparison: Polyaspartic vs. Traditional Polyurea and Epoxy

Major Application Areas

Because of its combined high performance, efficiency, aesthetics, and eco-friendliness, Polyaspartic is widely applied in areas with elevated standards:

1. Industrial Protection & Corrosion Control

• Protective coatings for chemical plants, sewage treatment facilities, offshore platforms, bridges, pipelines, storage tanks (inside & outside).
• Rust and corrosion prevention for steel structures.
• Concrete surface protection (against seepage, corrosion, wear).

2. High-Performance Flooring

• Ideal for high-wear, high-impact, high-chemical-resistance, hygienic, and visually protective floors in pharmaceutical plants, food and beverage factories, electronics workshops, labs, hospitals, warehouses, parking structures, malls, etc.
• Often used as a wear-resistant topcoat over epoxy or polyurethane mortar for ultimate protection and aesthetics.

3. Buildings & Infrastructure

• Waterproofing for roofs, terraces, balconies.
• Decorative and protective exterior coatings (color, texture, weather resistance).
• Waterproofing and protection in bridges, tunnels, culverts.
• Sports surfaces (tracks, courts, etc.).

4. Transportation

• Wear-resistant liners for trucks, trailers, containers.
• Deck and cabin protection coatings for ships.
• Wear and weather protection for wind turbine blades.

5. Other Applications

• Theme park structures, water parks.
• Wear linings and repair compounds.

Technical Challenges & Limitations

1. Higher Cost

Raw materials—especially polyaspartic resin—are costlier than epoxy resins or many polyurethane or traditional aromatic polyurea materials.

2. Moisture Sensitivity (Some Formulations)

Although more tolerant than conventional polyurea, some formulations remain vulnerable to very high humidity or moisture-laden substrates and may develop bubbles; compliance with construction specifications is essential.

3. High-Temperature Resistance

Long-term resistance to high temperatures (e.g., above 120 °C) may lag behind some specialty epoxy or organosilicone systems.

4. Substrate Preparation

As with all high-performance coatings, substrate cleanliness and roughness critically affect adhesion and final performance.

5. Formula Complexity

Performance highly dependent on formulation design (selection of polyaspartic resin, catalysts, additives), requiring high technical expertise.

Polyaspartic represents a significant advance in coating technology, integrating:

• The superior mechanical performance and chemical resistance of traditional polyurea,
• The convenient application (long open time) of epoxy resin, and
• The exceptional weather resistance and color/gloss retention of aliphatic systems.

Though more expensive, the total benefits in performance, process efficiency, and longevity make it irreplaceable in many high-end industrial and commercial applications. With ongoing technological advancements and cost reduction, its scope of use is expected to grow.

Feiyang has been specializing in the production of raw materials for polyaspartic coatings for 30 years and can provide polyaspartic resins, hardeners and coating formulations. Feel free to contact us: marketing@feiyang.com.cn

Our products list:

• Polyaspartic Resin
• Isocyanate Hardener
• Epoxy Hardener
• Special Chemical

Contact our technical team today to explore how Feiyang Protech’s advanced polyaspartic solutions can transform your coatings strategy. Contact our Tech Team