Brass Solenoid Valve Direct Acting

Product Specification

Z2 2 / 2 Way Direct Acting Solenoid Valve Normally Closed Sanmin Anti - Explosion Solenoid Valve

Applicability :

1 . The pipeline fluid must same as solenoid valve marked medium .

2 . Fluid temperature must be less than the marked temperature .

3 . About the working pressure difference , the pipeline high - pressure difference less than 0 . 04MPa should be chosen as Z , 2W , it is directly acting and direct - action step .
the pipeline high - pressure difference higher than 0 . 04MPa can choose polited type (differential) solenoid valve ;
Maximum working pressure difference should be less than the biggest calibration pressure of

solenoid valve ; General solenoid valve is a one - way work , so should pay attention to whether there is a contrast pressure , if you have to install the check valve .

4 . If fluid is not high cleanliness , should be installed a filters in front of the solenoid

valve , general solenoid valve is better claim to medium cleanness

5 . Pay attention to the environmental temperature on the influence of solenoid valve .

6 . Power supply current and power consumption should be selected according to the output

capacity , power supply voltage generally allow + / - 10 % , must pay attention to AC starting the

VA value is higher .

Reliability :

Ction time is very short at high frequency generally choose directly acting , large diameter

choose fast series .

Security :

Nominal pressure solenoid valve of the highest calibration must be more than the highest pressure in the pipeline, otherwise life will shorten or other unexpected circumstances .

Corrosive liquid should be chosen in all stainless steel type , appropriate chooses the corrosive fluid plastic king ( LF ) solenoid valve . Explosive environment must choose corresponding anti-explosion type .

Economy :

There are a lot of solenoid valve can be common use , but on the basis of can satisfy the above three terms , should choose the most economical products

Details                                                                                                                                                            

1 : 2 / 2 Way normally closed , closed when de - energized open , open when energized .

2 : Max pressure tolerance : 25 kgf / cm²

3 : Working Pressure : 0 ~ 20kgf / cm²

4 : Ambient temp : 0 ~ 65 ℃

5 : Flow as the arrow , mounts in any position ; best position is solenoid vertical and upright direction

6 : Only 1 / 4 " & 3 / 8" & 1 / 2 " connection size , orifice Φ 10mm , can be widely used in the corresponding flow and pressure system , replace the same connection size but big orifice valve , can save a lot of cost

7 : Voltage : AC220V / 230V / 240V / 110V / 24V / 50 / 60HZ DC24V / 12V

8 : Seals : can choose NBR , EPDM , VITON to fit the on / off control of different media

9 : Body : Brass

Why choose us                                                                                                                                              

1: Various style for each products and completely series pneumatic products .
2: Large stock for fast shipping .

3: Provide free products information .
4: Reliable quality assured and active after-sell service
5: One year quality guarantee

FAQ                                                                                                                                                               

Q: How much is our minimum order quantity ?
A: Our minimun quantity is 1 Piece .

Q: Could you offer the free samples ?
A: Yeah, we could offer the free samples based on special customer.pre-production sample,production sample.

Q: What ' s your business scope ?
A: Our business scope is SMC type high quality cylinder , air source treatment , solenoid valve ,water valve,steam valve, mechnical valve ,foot valve,angle seat valve,anti-explosion valve,pluse vlave, pneumatic valve ,hydraulic ball valve,hydraulic ss ball valve,hydraulic check valve,hydraulic solenoid valve ,all type of coil,lubrication pump and parts,SS316 fitting,quick coupler , etc .

Q: Do your company have specialized technical personnel ?
A: Design as your requirements,and have QC for make 100% inspection

Q: Can the product be made with our logo and brand ?
A: Yes , of course , we can make . we are OEM supplier for years and professional to make . But you need give us the authorization for work.