CY62157EV30LL-45BVXI Electronic IC Chips 8-Mbit (512K x 16) Static RAM

Product Specification

CY62157EV30 MoBL®

8-Mbit (512K x 16) Static RAM

Features

• TSOP I package configurable as 512K x 16 or as 1M x 8 SRAM

• High speed: 45 ns

• Wide voltage range: 2.20V–3.60V

• Pin compatible with CY62157DV30

• Ultra low standby power

  — Typical Standby current: 2 µA

  — Maximum Standby current: 8 µA (Industrial)

• Ultra low active power

  — Typical active current: 1.8 mA @ f = 1 MHz

• Easy memory expansion with CE1, CE2, and OE features

• Automatic power down when deselected

• CMOS for optimum speed and power

• Available in both Pb-free and non Pb-free 48-ball VFBGA,

  Pb-free 44-pin TSOP II and 48-pin TSOP I packages

Functional Description^[1]

The CY62157EV30 is a high performance CMOS static RAM organized as 512K words by 16 bits. This device features advanced circuit design to provide ultra low active current. This is ideal for providing More Battery Life™ (MoBL®) in portable applications such as cellular telephones. The device also has an automatic power down feature that significantly reduces power consumption when addresses are not toggling. Place the device into standby mode when deselected (CE₁ HIGH or CE₂ LOW or both BHE and BLE are HIGH). The input or output pins (IO₀ through IO₁₅) are placed in a high impedance state when:

 • Deselected (CE₁HIGH or CE₂ LOW)

  • Outputs are disabled (OE HIGH)

  • Both Byte High Enable and Byte Low Enable are disabled (BHE, BLE HIGH)

  • Write operation is active (CE₁ LOW, CE₂ HIGH and WE LOW)

To write to the device, take Chip Enable (CE₁ LOW and CE₂ HIGH) and Write Enable (WE) inputs LOW. If Byte Low Enable (BLE) is LOW, then data from IO pins (IO₀ through IO₇) is written into the location specified on the address pins (A₀ through A₁₈). If Byte High Enable (BHE) is LOW, then data from IO pins (IO₈ through IO₁₅) is written into the location specified on the address pins (A₀ through A₁₈).

To read from the device, take Chip Enable (CE₁ LOW and CE₂ HIGH) and Output Enable (OE) LOW while forcing the Write Enable (WE) HIGH. If Byte Low Enable (BLE) is LOW, then data from the memory location specified by the address pins appear on IO₀ to IO₇. If Byte High Enable (BHE) is LOW, then data from memory appears on IO₈ to IO₁₅.

Logic Block Diagram

Notes 1. For best practice recommendations, please refer to the Cypress application note AN1064, SRAM System Guidelines

Maximum Ratings

Exceeding maximum ratings may shorten the battery life of the device. User guidelines are not tested.

Storage Temperature .........................................................................–65°C to + 150°C

Ambient Temperature with Power Applied ...........................................–55°C to + 125°C

Supply Voltage to Ground Potential ................................–0.3V to 3.9V (V_CCmax + 0.3V)

DC Voltage Applied to Outputs in High-Z State ^{[6, 7]}.........–0.3V to 3.9V (V_CCmax + 0.3V)

DC Input Voltage ^{[6, 7]} .................................................... –0.3V to 3.9V (VCC max + 0.3V)

Output Current into Outputs (LOW) ....................................................................... 20 mA

Static Discharge Voltage ....................................... > 2001V (MIL-STD-883, Method 3015)

Latch up Current ............................................................................................... > 200 mA

Stock Offer (Hot Sell)