The toilet drain pipe wall row to row the Australian PVC pipe
toilet seat shifter
The drainage pipe diameter of the toilet is according to the
national standard, the minimum diameter is the sewage pipe of
DN100, and now it is generally used with u-pvc pipe, and the
minimum diameter is de110.2. If you are in your own home and are
subject to the height of the ground, you can also use the u-pvc
tube with a smaller de75.Generally, the size of the toilet drain is
5 to 6 cm, and the toilet S bend is usually 5 to 6 cm.The size of
the sewer pipe is generally about 110 cm.
|Name:||The toilet wall is rearranged to connect the joints.|
|Specification:||Use for Soil Pipe 102+-5 mm I.D|
|Processing method :||Assembly production|
Nowadays, every household must have the bathroom equipment --
toilet, how to install?Generally speaking, the installation of the
flush toilet more professional, is to provide services by merchants
in the stores, if there is no special instructions, freight and
installation fee included in the purchase and payment, you help a
friend pay attention to, be sure to check before installation
implement trace of usefulness, it is better that some implement
have water, may be during the inspection, do not matter.
Installation of a flush toilet drain pipe.
1. The waste pipe of the toilet shall be smooth, flat, free of air
bubbles, no cracks, no visible specks and sag in the inner wall of
the plastic pipe materials required by the national standards.How
are flush toilets installed
2. The pipe in the urinal has been set apart from the stench, so
there is no need to set the water trap on the sewage pipe,
otherwise it will affect the function of the toilet flushing.
3. Drain connection horizontal tube and vertical tube connection,
should use 445 degrees 5 ° inclined well were connected is
Installation steps of flush toilet.
1. Determine the installation position and hole in the ground to
the ground at outlet of drain pipe and the bottom of the toilet
bowl, according to the outside of the flush toilet base size, draw
the toilet on the ground points of fixed position of the hole, and
impact drill holes.The hole depth is about 5 cm.
2. Install the steel expansion bolt into the ground drilling with
the pedestal of the flush toilet seat, insert the bottom corner of
the toilet into the expansion bolt and tighten the nut to put the
toilet in place.The toilet drain is tightly connected with the
ground preset drain pipe and sealed.3. Install the tank (even
toilet doesn't need this step) according to the installation height
and water tank on back wall perforation position, the corresponding
fixed position on the metope of drilling and tapping into the steel
bolts, then put the water tank in place, make the back wall
perforation sets into the expansion bolt, add 3 mm thick nylon
washer on the nut and tighten.
4. Install the connecting pipe between the water tank and the
toilet seat (with copper pipe or plastic pipe, etc.), and the
connecting pipe between the inlet pipe and the bottom of the tank
(with stainless steel bellows, etc.).Inlet connection should be
equipped with Angle valve (inlet valve).
5. Install floating ball and other accessories in the water tank.
6. After opening the water inlet valve, the height of the floating
ball shall be adjusted according to the water inlet height required
in the water tank, and the tightness of its control screw shall be
adjusted according to the water spraying valve size.
7. After the tank is filled with water, check the toilet drain
capacity, and whether there is leakage in the connection of each
8. Seal the gap between the toilet seat and the floor with putty or
silica gel.Cement mortar or cement mortar shall not be used as
Install toilet seats and toilet seats.In addition, each house has a
different flush toilet to install the hole pitch, before buying the
toilet, must let the worker help you plan to measure well,
otherwise very likely the toilet that buys is installed not to go
up.Flush the toilet after the installation is complete, in the
first place to try flushing effect, the best way is: find a
cigarette butts thrown into, can just ran down, and the voice is
not big, the install link no problem.
The above is all about how to install the toilet bowl, the
information is for reference only!